Configuring BIRD as a BGP Route Reflector

These instructions will take you through installing BIRD as a BGP route reflector, and updating your other BIRD instances to speak to your new route reflector.

These instructions are valid for both Ubuntu 14.04 and RHEL 7.


Before starting this you will need the following:

  • A machine running either Ubuntu 14.04 or RHEL 7 that is not already being used as a compute host.
  • SSH access to the machine.


Step 1: Install BIRD

Ubuntu 14.04

Add the official BIRD PPA. This PPA contains fixes to BIRD that are not yet available in Ubuntu 14.04. To add the PPA, run:

sudo add-apt-repository ppa:cz.nic-labs/bird

Once that’s done, update your package manager and install BIRD (the single bird package installs both IPv4 and IPv6 BIRD):

sudo apt-get update
sudo apt-get install bird


First, install EPEL. Depending on your system, the following command may be sufficient:

sudo yum install epel-release

If that fails, try the following instead:

sudo yum install epel-release-7-9.noarch.rpm

With that complete, you can now install BIRD:

yum install -y bird bird6

Step 2: Set your BIRD IPv4 configuration

Before doing this, you’ll need to take note of what BGP AS number you’ve used in your compute node install.

Open /etc/bird/bird.conf on your route reflector system and initially fill it with the following template, replacing <router_id> with the IPv4 address of your route reflector:

# Configure logging
log syslog { debug, trace, info, remote, warning, error, auth, fatal, bug };
log stderr all;

# Override router ID
router id <router_id>;

filter import_kernel {
if ( net != ) then {

# Turn on global debugging of all protocols
debug protocols all;

# This pseudo-protocol watches all interface up/down events.
protocol device {
  scan time 2;    # Scan interfaces every 2 seconds

Then, at the end, for each compute node in your deployment add one of the following blocks, replacing <node_shortname> with a purely alphabetical name for the host (this must be unique for each host, but the shortname is only used within this file), <node_ip> with the node’s IPv4 address, and <as_number> with the AS number you’re using:

protocol bgp <node_shortname> {
  description "<node_ip>";
  local as <as_number>;
  neighbor <node_ip> as <as_number>;
  rr client;
  graceful restart;
  import all;
  export all;

Step 3 (Optional): Set your BIRD IPv6 configuration

If you want to use IPv6 connectivity, you’ll need to repeat step 2 but using /etc/bird/bird6.conf. The only differences between the two are:

  • the filter needs to filter out ::/0 instead of
  • where before you set <node_ip> to the compute node’s IPv4 address, this time you need to set it to the compute node’s IPv6 address

Note that <router_id> should still be set to the route reflector’s IPv4 address: you cannot use an IPv6 address in that field.

Step 4: Restart BIRD

Ubuntu 14.04

Restart BIRD:

sudo service bird restart

Optionally, if you configured IPv6 in step 3, also restart BIRD6:

sudo service bird6 restart


Restart BIRD:

systemctl restart bird
systemctl enable bird

Optionally, if you configured IPv6 in step 3, also restart BIRD6:

systemctl restart bird6
systemctl enable bird6

Step 5: Reconfigure compute nodes

If you used the script to configure your compute hosts, and you used the route reflector IP when you did, you do not need to do anything further.

Otherwise, on each of your compute nodes, edit /etc/bird/bird.conf (and, if you’re using IPv6, /etc/bird/bird6.conf) to remove all their peer relationships (the blocks beginning with protocol bgp) except for one. Edit that one’s neighbor field IP address to be the IP address of the route reflector (either IPv4 or IPv6). Then, restart their BIRD instances as detailed in step 4.